Fast & Easy Board and Batten Wall (2024)

Add character to any room with a DIY board and batten wall.

It’s week 3 of the $100 Bathroom remodel! This week we are starting to add style to the space. And to fill up the large wall opposite the vanity, I create a board and batten wall to add interest.

Board and batten is such a great tool to add interest and character to a wall. Older homes, that you always hear referred to as “full of character” never had boring walls.

Instead they had texture created by wood on the walls. You can still add artwork and more to walls with board and batten, but just the simple design and texture of the wall treatment behind the decor makes the room feel complete.

This post may contain affiliate links. As an Amazon Associate I earn from qualifying purchases. Click here to read my full disclosure policy.

Fast & Easy Board and Batten Wall (1)

Update: Our bathroom remodel is (mostly) done! You can check out the plan, with lots of tips, in this budget bathroom design plan. The week 2 remodel update includes tips and ideas for demo. We installed inexpensive peel and stick flooring and our new budget friendly open vanity was an easy DIY.

You can see the final budget bathroom remodel reveal here!

Board and Batten in a Bathroom

One of the best things about adding a board and batten wall to a bathroom is it creates a place to add hooks or a towel bar.

Trying to perfectly space hooks on a wall means you almost never hit a stud. Since studs are typically 16″ apart in a wall, if you want to add 3 hooks, you would need them to be 16″ apart or have most of the hooks not in a wall.

The same goes for adding a towel bar. If your towel bar is 24″ wide, then only one side can be in a stud in the wall.

Fast & Easy Board and Batten Wall (2)

Not having the hooks or towel bar in a stud means it will eventually wiggle itself loose and fall out. This process is usually sped up a lot if you have kids using the towel rack or hooks in your bathroom.

And the use of wall anchors can slow down this process, but any amount of weight over time had been show to still cause issues with hooks or towel bars just attached into the drywall.

This is where the board and batten wall is amazing! You are adding strips of wood to the wall, which are attached to the studs. Then you are able to attach you hooks or towel bars directly to the boards and viola… they are secure and stay put!

Even with lots of use by kids or adults, you do not have to worry about your towel bars coming loose. Plus the added character the board and batten wall adds makes your bathroom pretty amazing!

Fast & Easy Board and Batten Wall (3)

Designing a Board and Batten Pattern

There are so many different board and batten patterns you can add to a wall. So even if you don’t want super traditional design, you can still add a board and batten wall.

We went with a traditional board and batten design in our bathroom. This design is a horizontal board on top and bottom with vertical boards in the center.

Since the space is broken up with the tub/shower, a full wall design would have been more challenging and not what I was going for in the space.

Fast & Easy Board and Batten Wall (4)

I did add a bit to the traditional design to give make it unique and add some functionality. A second horizontal board close to the top was added to added. This board is the perfect height for the hooks we need to hand towels on for the kids.

I also added a double vertical board design instead of using just one evenly spaced along the wall. This was done to help cover up the hole in the wall where the door handle hit the drywall.

Now that you understand why we chose the design we did, here are some examples of other board and batten walls to inspire you to DIY your own.

Traditional Board and Batten Designs

The most common board and batten design a top and bottom board with evenly spaced vertical boards in between. The more traditional option is to end the board and batten at a standard chair rail height (between 30-36″ off the floor).

But you can change the height of this board and batten to anything you want. Typically you want to not cut the room in half so you would go for either a 1/3 or 2/3 height. But it’s your house so you can do what you want!

Fast & Easy Board and Batten Wall (5)

You can also use the common board and batten design but take it all the way to the ceiling. This instantly looks a bit more modern and creates a beautiful feature wall in your room.

Fast & Easy Board and Batten Wall (6)

Another traditional board and batten design is to add a third horizontal board. This creates a section of cubes at the top of the board and batten wall.

In the drawing below, I split the room in half with the wall, but the addition of the extra board help to still give it the 1/3 rule. You can also raise or lower this board and batten design anywhere you want on your wall.

Fast & Easy Board and Batten Wall (7)

And this third horizontal board design can also be adapted for a full board and batten wall. To keep it traditional, the center horizontal line would be a chair rail height (30-36″ off the floor).

Fast & Easy Board and Batten Wall (8)

Modern Board and Batten Designs

With the popularity of DIY, you are starting to see so many different board and batten wall designs. The possibilities are endless and you can easily do a search for more ideas, but here are a few to get you started.

This first one is a modern take on the traditional full wall design. This one uses thin vertical strips to add more texture to the wall. And you can space them closer together for even more texture.

Fast & Easy Board and Batten Wall (9)

Plus, to make this design even more modern, leave the horizontal boards off completely. This will let the vertical boards disappear right into the ceiling.

This board and batten design is harder to get a clean paint line at the top so I would recommend painting the wall and the boards before attaching them. Then you just have to touch up the paint over the nail holes and caulk.

Fast & Easy Board and Batten Wall (10)

Another fun design is to create cubes with your board and batten wall. You can space them out tighter like in the drawing below or make the cubes larger.

You could also add the full vertical boards, then stagger the horizontal boards of the cubes for more interest.

Fast & Easy Board and Batten Wall (11)

To take your board and batten wall to the next level, you can add boards at an angle. Something as simple as cutting the boards at a 30 degree angle (like in the picture below) will add interest to you wall.

Or you can get creative and add cuts all all different angles to create a piece of art on your wall.

Fast & Easy Board and Batten Wall (12)

You can also attach angled boards in a pattern like this chevron board and batten wall design. This design might look complicated, but is actually a lot of easily repeatable cuts. All together you get a bold statement in your room.

Think of modern board and batten walls more like a giant piece of art in your room. And have fun creating any design that you want!

$100 Bathroom Remodel Update

Since it is Week 3 of the DIY bathroom makeover as part of the $100 Room Challenge, I want to quickly check in on the entire room and budget! Also, at the end of the post, you can also check out the progress of all the other bloggers participating in the $100 Room Challenge.

We installed peel and stick vinyl tiles that we had left over from our DIY kitchen remodel. Luckily the bathroom was small so we had plenty of tiles and underlayment scraps.

Fast & Easy Board and Batten Wall (14)

Then I installed the board and batten wall and painted it this beautiful grayish turquoise color. The paint was free because I borrowed it from my father-in-law who had left overs after painting his rental house.

Bye-bye forever florescent green!

Borrowing paint is a great option for adding color to a room on a budget! And people with left over paint are usually happy to part with it instead of them having to store it or pay to dispose of it.

Fast & Easy Board and Batten Wall (15)

Remodel Budget:

  • Demo – $0
  • Moving drain pipe – $2.00 (for pipe elbows)
  • Repair holes – $0 (had drywall mud left over from other project)
  • New gray paint – $0 (had one roller on hand and will wash and reuse)
  • New turquoise paint – $0 (borrowed paint and used small roller on hand)
  • New Floor – $0 (used leftovers from kitchen remodel)
  • MDF boards for board & batten – $32.00
  • Caulk – $2.50
  • New faucet with drain – $24.00

Total: $60.50

Luckily I still have a good amount of money in my budget because this week we are building a vanity and need a new vanity top and sink!

Plus I am hoping to have some money left over for a new shower curtain too. Wish me luck!

DIY Board and Batten Wall

Tools Needed:

  • Saw
  • Finish nail gun
  • Level
  • Measuring tape
  • Caulk gun

Supplies:

  • MDF (medium density fiberboard) boards
  • 2″ finish nails
  • Wood filler
  • Paintable caulk

Choosing your Boards

We used 1×4 MDF boards for our wall. But you can use any boards you want. I recommend MDF because it is inexpensive and very smooth without a lot of sanding. This means it will look amazing once painted.

The 1×4 MDF board are typically 5/8″ thick and 3 1/2″ wide. You can change the width of your boards to any width you want for your design.

Also, if you want a shallower board and batten design, you can also rip down 1/2″ or 1/4″ MDF plywood to your desired width. Using MDF plywood means you can create any design and are not limited to standard dimensional lumber sizes.

Add the Horizontal Boards

Measure and mark where you want the bottom of the top board. If you are doing a full wall, you can skip this.

Locate your wall studs and mark where they are.

Measure the width of the wall and cut your board to this measurement. Make sure to take the measurement at the lines you just marked because walls are not always straight.

Fast & Easy Board and Batten Wall (16)

Cut your first board.

Line it up on the wall with your measurements, then use a level to make sure the board is level.

Fast & Easy Board and Batten Wall (17)

Attach it to the wall with the 2″ long finish nails. Make sure to attach it into the wall studs. The longer nails are necessary to attach the boards to the studs through the drywall.

Fast & Easy Board and Batten Wall (18)

Once the first board is attached, cut and attach the bottom board at the floor.

Add Vertical Boards

If you are adding more horizontal boards, cut the shorter vertical boards first. Make sure all these pieces are cut the same length, that way when they are attached, the next horizontal board will already be level.

Measure where you want your vertical boards to go.

Fast & Easy Board and Batten Wall (19)

I started by attaching the smaller boards to the edges of the wall, then measured from there for the rest of my boards.

When attaching the vertical boards, make sure to level them before attaching as well. Then secure with nails.

These might not all be into studs, if you want more holding power, you can use a liquid nails on the back of the boards before attaching.

Fast & Easy Board and Batten Wall (20)

Now you can measure and cut the middle horizontal board. Press it firmly to the bottom of the horizontal boards and attach it into the studs.

Fast & Easy Board and Batten Wall (21)

Now you will need to measure for each of the vertical boards. Since floors are not always level, if you only measure in one spot the boards might be the wrong size.

Instead measure exactly where you are going to be attaching the boards to the wall. Cut the boards to that measurement.

Fast & Easy Board and Batten Wall (22)

When installing these boards, you may have to tap them into place. Place a block where you want to tap it with the hammer to prevent damaging your boards.

Fast & Easy Board and Batten Wall (23)

Make sure to level the vertical boards, then attach them with the nail gun.

Fast & Easy Board and Batten Wall (24)

Finishing your Board and Batten Wall

Once all the boards are attached, you can fill the the nail holes with wood filler. I also filled any gaps in between the boards.

Then sand the wall to get it nice and smooth.

Fast & Easy Board and Batten Wall (25)

Finally, caulk all the seams with a paintable caulk. This will seal the edges where the boards meet the wall and make it look like one. It will also help fill in any gaps where the wall is not totally straight to the boards.

Fast & Easy Board and Batten Wall (26)

Let the caulk dry, then it is time to paint! I was so excited to finally say good-by to the vibrant green in this tiny bathroom.

You can paint your board and batten a contrasting color to your walls, or paint it the same color as the walls. Either way, the texture and character of the board and batten will still be there.

Fast & Easy Board and Batten Wall (27)

I love how the new wall looks in the bathroom. It gives the small space so. much style. And it was super easy on our budget!

Just think of all the places you could add some variety of board and batten to your home. It is a fun and easy weekend project.

Fast & Easy Board and Batten Wall (28)

Happy DIYing!

Fast & Easy Board and Batten Wall (29)

And don’t forget to check out the progress all the other bloggers are making on their $100 Room Makeovers. We only have 1 week left until reveal day!!!

You are invited to the Inlinkz link party!

Click here to enter

Fast & Easy Board and Batten Wall (2024)

FAQs

What's the cheapest way to do board and batten? ›

Using mdf board, which is lightweight and inexpensive. Using battens only 1/4 inch thick so the baseboards did not need to be removed. Skipping a horizontal line of board installed above the baseboards (as people include with some styles) Skipping nailing flat boards into the drywall under the battens.

What is a cheaper alternative to board and batten? ›

Fiber cement is the cheapest material for board and batten siding. It costs around $0.75 to $5 per square foot only. Fiber cement is a mixture of three different materials.

What is the best material for board and batten walls? ›

While all types of wood are great to use as board and batten siding material, cedar is the most preferred species of timber by homeowners as well as builders. Generally, cedar is much more durable compared to other wood species.

How long does it take to make a board and batten wall? ›

How Long Does It Take To Make A Board And Batten Wall? For a wall of about 8×8 feet, cutting and installation can take approximately 3 hours. Be mindful that preparation and finishing steps require additional time. Plan for a weekend to ensure a seamless project.

What are the disadvantages of board and batten? ›

The cons include: It can take a long time to install – There is a high number of board and battens that need to be installed with this type of siding, which is why you'll need to make sure it's properly installed.

What is an alternative to batten board? ›

Board and batten crafted from a modern material like fiber cement is the much better alternative to vinyl board and batten siding. With fiber cement, homeowners can be confident that their home exterior will continue to look great season after season.

Why is board and batten so expensive? ›

The cost of achieving the board and batten look varies according to home size, style, type of materials and professional labor. Size – As expected, larger homes require more materials and labor. Design – Unusual or more complicated designs require additional labor time measuring, cutting and installing.

Which is better shiplap or board and batten? ›

Conclusion. Board and batten and shiplap are both outstanding choices for residential design, each with its own charm and versatility. Board and batten's vertical orientation and elegant lines add a touch of sophistication, while shiplap's horizontal profile invites a cozy and rustic feel.

Are board and batten walls outdated? ›

While board and batten is still a reliable and sturdy wall covering, over the years it has also evolved into a timeless style choice.

Do board and batten need to be nailed to studs? ›

If you're using thin, lightweight lumber, you won't need to stress about it. However, for everything else, it's a good idea to attach your boards to the studs wherever possible. If you can't find a wall stud, use wood glue/liquid nails and a nail that's long enough to secure the wood to the wall.

Should you paint the wall before board and batten? ›

Step 4: Paint the Wall

To make things easy, paint the wall before you start nailing your design on. Trust me - this is the easiest way to do this!

Do you have to remove baseboards for board and batten? ›

You don't have to remove your baseboards. No complicated measuring here – using my method, depending on the length of your wall, your battens will be between approximately 8-16 inches apart. The easy way to deal with outlets and switches – probably not the most professional way, but hey, the goal is EASY here!

Do you nail or glue board and batten? ›

Install battens

Now you're ready for the battens! You have two options when it comes to installing the batten boards: Use nails only (easier to remove down the line without drywall damage) Use construction adhesive and nails (much more permanent)

How much does DIY board and batten cost? ›

DIY Board and Batten Siding Installation vs. Hiring a Professional. The cost to install board and batten siding yourself is between $0.75 and $10 per square foot.

How much does it cost to board and batten a wall? ›

The total cost to install board and batten siding averages $2.25 to $12.50 per square foot. While professionals will likely give you one per square foot price that includes both materials and installation, their labor typically comes out to about $1.75 to $2.25 per square foot.

How much does it cost to board and batten? ›

The total cost to install board and batten siding averages $2.25 to $12.50 per square foot. While professionals will likely give you one per square foot price that includes both materials and installation, their labor typically comes out to about $1.75 to $2.25 per square foot.

What kind of boards do you use for DIY board and batten? ›

Both wood and MDF are common for board and batten installation. MDF is easier to work with, smoother, and more cost-effective. Wood is solid and more durable, and ideal for wet areas, but you'll need to use a high quality wood that has no knots or warping (this will increase the cost).

Is board and batten cheaper than vinyl? ›

Vinyl is less expensive than other siding materials like wood or fiber cement in the board batten style but more expensive than your traditional horizontal vinyl siding.

References

Top Articles
Latest Posts
Article information

Author: Greg O'Connell

Last Updated:

Views: 6080

Rating: 4.1 / 5 (42 voted)

Reviews: 81% of readers found this page helpful

Author information

Name: Greg O'Connell

Birthday: 1992-01-10

Address: Suite 517 2436 Jefferey Pass, Shanitaside, UT 27519

Phone: +2614651609714

Job: Education Developer

Hobby: Cooking, Gambling, Pottery, Shooting, Baseball, Singing, Snowboarding

Introduction: My name is Greg O'Connell, I am a delightful, colorful, talented, kind, lively, modern, tender person who loves writing and wants to share my knowledge and understanding with you.